Two Wheel Fix

Two Wheel Fix (http://www.twowheelfix.com/index.php)
-   Mechanical or Tech (http://www.twowheelfix.com/forumdisplay.php?f=13)
-   -   Heat Wrap (http://www.twowheelfix.com/showthread.php?t=21337)

No Worries 05-13-2012 11:22 PM

Heat Wrap
 
My friend has a 650 V-Strom. The front cylinder's exhaust pipe is a 1/4 inch at the bottom from the oil cooler.

http://img580.imageshack.us/img580/2889/vstrom1.jpg

We decided to wrap the pipe with fiberglass heat wrap. We used gloves to avoid the glass fibers. We put the black fiberglass in water first and then wrapped. What a mess. We used pipe clamps to keep the ends of the wrap from unraveling.
http://img52.imageshack.us/img52/637/vstrom2.jpg

The next day he took the bike out and the gauge registered hotter. We cut the fiberglass off after that. We're not sure why the bike didn't run cooler.

askmrjesus 05-14-2012 12:55 AM

Quote:

Originally Posted by No Worries (Post 512336)

The next day he took the bike out and the gauge registered hotter. We cut the fiberglass off after that. We're not sure why the bike didn't run cooler.

Exhaust wrap is actually meant to increase the exhaust and header gas temps.

Since an engine is basically a big air pump, the faster you can move the air, the faster the engine goes, (up to a point).

The idea behind exhaust wrap, is to heat the exhaust so that the density of the exhaust decreases. The lower the density, the faster lower temp intake gases will flow towards it. It's like wind at the beach. The hotter the land mass, the faster the wind will blow cooler air on shore.

Problem is, the hotter exhaust gas, means a hotter pipe, which means a hotter head and cylinder, which means you've gone backwards in the cooling department.

JC

pauldun170 05-14-2012 09:40 AM

1 Attachment(s)
Quote:

Originally Posted by askmrjesus (Post 512337)
Exhaust wrap is actually meant to increase the exhaust and header gas temps.

Since an engine is basically a big air pump, the faster you can move the air, the faster the engine goes, (up to a point).

The idea behind exhaust wrap, is to heat the exhaust so that the density of the exhaust decreases. The lower the density, the faster lower temp intake gases will flow towards it. It's like wind at the beach. The hotter the land mass, the faster the wind will blow cooler air on shore.

Problem is, the hotter exhaust gas, means a hotter pipe, which means a hotter head and cylinder, which means you've gone backwards in the cooling department.

JC

...

askmrjesus 05-14-2012 01:16 PM

:lol:

JC

Particle Man 05-14-2012 01:47 PM

Why are you trying to get it to run cooler?

Captain Morgan 05-14-2012 03:28 PM

Have you considered relocating the oil cooler? Many of the skid plates require relocation of the oil cooler to a vertical position at the side. I haven't done that to mine, but know it's a possibility. Touratech sells a relocation kit. Here's a link to the kit on their website. http://www.touratech-usa.com/Store/1...-V-Strom-DL650

Here's a pic of a modified oil cooler that's been relocated as I described.

http://i289.photobucket.com/albums/l...n/IMG_4972.jpg

No Worries 05-15-2012 12:34 AM

Quote:

Originally Posted by Particle Man (Post 512350)
Why are you trying to get it to run cooler?

Just thought it was bad engineering to have the oil cooler right behind the exhaust pipe. Seems that the cooler was taking in more heat than it was expelling.

Quote:

Originally Posted by Captain Morgan (Post 512352)
Have you considered relocating the oil cooler? Many of the skid plates require relocation of the oil cooler to a vertical position at the side. I haven't done that to mine, but know it's a possibility. Touratech sells a relocation kit. Here's a link to the kit on their website. http://www.touratech-usa.com/Store/1...-V-Strom-DL650

Here's a pic of a modified oil cooler that's been relocated as I described.

http://i289.photobucket.com/albums/l...n/IMG_4972.jpg

Thanks Captain, that looks cool.

No Worries 05-15-2012 12:40 AM

Quote:

Originally Posted by askmrjesus (Post 512337)
Exhaust wrap is actually meant to increase the exhaust and header gas temps.

Since an engine is basically a big air pump, the faster you can move the air, the faster the engine goes, (up to a point).

The idea behind exhaust wrap, is to heat the exhaust so that the density of the exhaust decreases. The lower the density, the faster lower temp intake gases will flow towards it. It's like wind at the beach. The hotter the land mass, the faster the wind will blow cooler air on shore.

Problem is, the hotter exhaust gas, means a hotter pipe, which means a hotter head and cylinder, which means you've gone backwards in the cooling department.

JC

That sounds right. He just saw the temp gauge higher. I don't think he noticed if the bike was any faster.

askmrjesus 05-15-2012 08:30 AM

Quote:

Originally Posted by No Worries (Post 512372)
That sounds right. He just saw the temp gauge higher. I don't think he noticed if the bike was any faster.

Any gains in performance would be modest at best.

JC

derf 05-15-2012 12:32 PM

Quote:

Originally Posted by askmrjesus (Post 512377)
Any gains in performance would be modest at best.

JC

What crack are you smoking? That .05 hp gain from the wrap adds enough go to make rossi run for his money


All times are GMT -4. The time now is 05:33 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.