Two Wheel Fix - View Single Post

RACER X · 10-04-2009, 01:02 AM

so i got around to installing my HID's

thanks to this thread, it was alot easier

http://www.hayabusa.org/forum/gen-ii...l-removal.html

thanks fella;s

TRY AN AVOID TOUCHING THE ACTUAL BULB!

this is to show basically the entire kit.
your going to eventually cut the clear plastic over the bulb itself and discard it.
i ended up cutting the plastic grommet that held all the wires.
i also cut off some black piece that is show in pic #6
The red and black spades plug into the OE harness. Red - WHITE in the OE harness and Black - BLACK in the OE

everything else pretty much plugs into itself.

to show how small the ballast is

i put everything on the right side, the left has fuses and such

i ended up routing the wiring thru this spot

I also ended up cutting this piece out too, not sure whats is for.

i ended up cutting this grommet thingy out as it prevent the dust cover from closing completely.

this is all you really need coming out of the dust cover (the red and black spades that plug into the OE harness) , i ended up shoving that rubber grommet i cut off, inside the outer tip of this cover to try and keep some water out.

ended up using the double sided tape to hold down the ballast and ignitor (the smaller black box) have an assortment of zip ties ZIC

plug everything together , zip tie as much as possibe.

its really an easy job and if your in town i'd help you put it together. i would say really about an 1/2 hr job. plan ahead. cuz i had to cut alot of elec tape that i had around the OE harness of a few times cuz i found a better path

only shot i have as its raining now, and i also cleaned up my bike

hope this helps

DDM Tuning - HID Kits, HID Bulbs, DEPO Lighting, BMW and Porsche Performance Accessories
$54 delivered
35w 5000k

10-04-2009, 01:02 AM	#1
RACER X AMA Supersport Join Date: Nov 2008 Location: Richmond, Tx Moto: '10 Tuono Factory Posts: 4,569	DDM HID install GENII Busa so i got around to installing my HID's thanks to this thread, it was alot easier http://www.hayabusa.org/forum/gen-ii...l-removal.html thanks fella;s TRY AN AVOID TOUCHING THE ACTUAL BULB! this is to show basically the entire kit. your going to eventually cut the clear plastic over the bulb itself and discard it. i ended up cutting the plastic grommet that held all the wires. i also cut off some black piece that is show in pic #6 The red and black spades plug into the OE harness. Red - WHITE in the OE harness and Black - BLACK in the OE everything else pretty much plugs into itself. to show how small the ballast is i put everything on the right side, the left has fuses and such i ended up routing the wiring thru this spot I also ended up cutting this piece out too, not sure whats is for. i ended up cutting this grommet thingy out as it prevent the dust cover from closing completely. this is all you really need coming out of the dust cover (the red and black spades that plug into the OE harness) , i ended up shoving that rubber grommet i cut off, inside the outer tip of this cover to try and keep some water out. ended up using the double sided tape to hold down the ballast and ignitor (the smaller black box) have an assortment of zip ties ZIC plug everything together , zip tie as much as possibe. its really an easy job and if your in town i'd help you put it together. i would say really about an 1/2 hr job. plan ahead. cuz i had to cut alot of elec tape that i had around the OE harness of a few times cuz i found a better path only shot i have as its raining now, and i also cleaned up my bike hope this helps DDM Tuning - HID Kits, HID Bulbs, DEPO Lighting, BMW and Porsche Performance Accessories $54 delivered 35w 5000k __________________ ΜΟΛΩΝ ΛΑΒΕ 2014 GROM! 181cc of FURY 2010 Aprilia Tuono Factory - SOLD 2009 SFV Gladius - SOLD 2008 Hayabusa - SOLD.