Go Back   Two Wheel Fix > In the Garage or Shop > Mechanical or Tech

Reply
 
Thread Tools Display Modes
Old 02-14-2012, 04:10 PM   #1
No Worries
Keyboard Racer
 
No Worries's Avatar
 
Join Date: Feb 2008
Location: Mile High City
Moto: Old Superbikes
Posts: 1,016
Default Changing a stator

Has everyone heard how awesome the old Suzuki GS's are? If not, I'm sure you heard about the electronic problems. I'm the original owner of a 79 GS1000. In 33 years, I've had one electrical fire, two stators that went bad, and one rectifier, and two regulators that went bad (they were separate back then).

It originally came with points ignition. In the early 80's I changed to Dyna coils and Dyna electronic ignition. The ignition advance is still by weights and springs. They work good as long as I spray some grease on them every couple years. I originally put on carbon-core sparkplug wires, but changed to solid copper wires. The damn thing starts instantly, all the time.

Last summer, I took the bike to a local bakery. When I came out, the neutral and oil pressure lights came on, but when I pressed the start button, the lights went out and there was no cranking. I pushed the bike across the street to an auto repair shop and told them I had a dead battery. They brought out this wheeled-charger with huge copper battery clamps. I swear you could have welded thick steel with them. It took me several minutes, but I was able to fit them on the little battery screws. After several minutes of charging, the bike started right up.

I went home and stuck a voltmeter on the battery. The voltage stayed the same. I decided to replace the separate R/R's with a single R/R. I also cleaned all the connections. Didn't change. So I got a new stator. The below pictures show the details.

The cylinder cooling fins are on the upper left, the starter is on the upper center, and the stator is in the cover. Even though it is in an oil bath, notice how burned the windings look. I believe I put this one in circa 1990.

This picture shows a cardboard copy of the gasket I made for the bolts. Thy are all the same size, but all are different lengths. Big timesaver.

Here's the new stator installed. The big tool between the screwdriver and hammer is an impact wrench. It's the only way to get those phillips-head screws off without stripping the heads.

Here's the voltmeter reading with new stator and R/R. Perfect. When I went back to the bakery, I bought a dozen donuts for the guys at that repair shop.
No Worries is offline   Reply With Quote
Old 02-14-2012, 04:31 PM   #2
pauldun170
Serious Business
 
pauldun170's Avatar
 
Join Date: Nov 2008
Location: New York
Moto: 1993 ZX-11 2008 CBR1000rr
Posts: 9,723
Default

Quote:
Originally Posted by No Worries View Post
Has everyone heard how awesome the old Suzuki GS's are? If not, I'm sure you heard about the electronic problems. I'm the original owner of a 79 GS1000. In 33 years, I've had one electrical fire, two stators that went bad, and one rectifier, and two regulators that went bad (they were separate back then).

It originally came with points ignition. In the early 80's I changed to Dyna coils and Dyna electronic ignition. The ignition advance is still by weights and springs. They work good as long as I spray some grease on them every couple years. I originally put on carbon-core sparkplug wires, but changed to solid copper wires. The damn thing starts instantly, all the time.

Last summer, I took the bike to a local bakery. When I came out, the neutral and oil pressure lights came on, but when I pressed the start button, the lights went out and there was no cranking. I pushed the bike across the street to an auto repair shop and told them I had a dead battery. They brought out this wheeled-charger with huge copper battery clamps. I swear you could have welded thick steel with them. It took me several minutes, but I was able to fit them on the little battery screws. After several minutes of charging, the bike started right up.

I went home and stuck a voltmeter on the battery. The voltage stayed the same. I decided to replace the separate R/R's with a single R/R. I also cleaned all the connections. Didn't change. So I got a new stator. The below pictures show the details.

The cylinder cooling fins are on the upper left, the starter is on the upper center, and the stator is in the cover. Even though it is in an oil bath, notice how burned the windings look. I believe I put this one in circa 1990.

This picture shows a cardboard copy of the gasket I made for the bolts. Thy are all the same size, but all are different lengths. Big timesaver.

Here's the new stator installed. The big tool between the screwdriver and hammer is an impact wrench. It's the only way to get those phillips-head screws off without stripping the heads.

Here's the voltmeter reading with new stator and R/R. Perfect. When I went back to the bakery, I bought a dozen donuts for the guys at that repair shop.
image shack blocked at work.
Looking forward to revisiting this post later on.
__________________


Quote:
Originally Posted by Dave View Post
feed your dogs root beer it will make them grow large and then you can ride them and pet the motorcycle while drinking root beer
pauldun170 is offline   Reply With Quote
Old 02-24-2012, 11:13 AM   #3
azoomm
moderator chick

 
azoomm's Avatar
 
Join Date: Feb 2008
Location: Hill Country TX
Moto: Pasta Rockets
Posts: 8,917
Default

Quote:
Originally Posted by No Worries View Post
This picture shows a cardboard copy of the gasket I made for the bolts. Thy are all the same size, but all are different lengths. Big timesaver....
Timesaver is right!! It's a simple tip that goes a long way on reassembly.

How's it running?
__________________
We have enough youth. How about a fountain of "smart"?

Come Play at the Track!!

http://www.elitetrackdays.com
azoomm is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:29 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.