The Great R6 (re)Build

[t-homo]

Originally Posted by DLIT

Got your text. I want pics of said flames shooting out the exhaust (I don't have the slightest doubt they are).

I said that too. His response was something similar to "Blah blah blah, i'f a fucking cunt."

[mondos06cbr1000]

gonna be sick dude

[Amber Lamps]

I don't doubt flames either,especially if you're using a generic map 'cause Dynojet tends towards the rich side for liability reasons. Congrats bro' I'm glad it'sall working out for you! Good call on the cf can btw carbon fiber FTW!

[ceo012384]

Originally Posted by TIGGER

I don't doubt flames either,especially if you're using a generic map 'cause Dynojet tends towards the rich side for liability reasons.

Yeah the flames are just because it's rich... I threw that map on there temporarily. It's getting a custom map on Thursday.







Made huge progress on the bike a little while ago but have been to busy to post it up until now... It's pretty much done though.



Mounted up the new radiator and filled with engine ice:



Removed the stock O2 sensor and installed the PCIII... downloaded the DynoJet map for my setup on there temporarily until I get a map:



Mounted up the new gas tank:



Filled her up with oil and gas, and also had to fill and bleed the rear brake since I installed the banjo pressure switch, then took her outside to start that bitch up.

Started up right away, and that exhaust is SICK. Sounds great. Not to mention that since the DynoJet maps are set pretty rich, she shoots big flames on decel

I'm pretty disappointed with the sound in this video... maybe the microphone on my camera doesn't pick up the lower frequencies as well. This video doesn't do it justice at all, I plan to take another one next time I go out there... The camera doesn't pick up the deepness very well and the frame rate doesn't pick up most of the flameshooting. Anyways, here it is:

http://youtube.com/watch?v=SAHLl_xkkyk

Then Wednesday my good buddy Dennis helped me cut/drill/mount the race bodywork since I'd never done it before. The fit was pretty spot-on, the flexibility of the stuff is great.

Mounted up:









Then Dennis left and I cut spots for the frame sliders. Cut and mounted, right:



Left:



Mounted the new set of tank sliders. Looks like Traxxion went to a glossier finish of plastic which is nice, they definitely blend in more nicely now:





Threw on some sexy TWFix stickers as well:





Then I took all that off and mounted up all the street stuff so I could check that all the wiring still worked, as well as cut the street fairings for the frame sliders, like so:



Then I stripped her all down again, and got everything I'm painting ready for paint. The full set of track bodywork, the airbox cover, my backup gas tank, the stock fender and the two midfairings:



Now she's just hanging out waiting for next week's track days, as am I




Oh and lastly since a ziptie bit the wire of my camera lens I repaired that by splicing it open and using four inline crimp bullet connectors which afterwards I wrapped all up with electrical tape:





Thursday at 2pm I'm getting a dyno and custom map done for the bike. Monday on my way up to the track I'll be grabbing the bodywork. Looks like everything will be together in time... except the decals, I'll throw those on when I get back from the track.

Can't wait to get her on the track. I'm psyched.

[DLIT]

Lemme see a shot of the left side's slider. I want to see how much you had to cut.

[Amber Lamps]

I'll tell you one thing Motherfucker,if I EVER need sliders cut in...I'M CALLING YOUR ASS!!!!!! I don't think I've ever seen more perfectly cut sliders in my life!!! Good job! Oh and Dlit,if it's the same as my bike,they give you a sticker template to cut by with the kit.

[ceo012384]

Originally Posted by DLIT

Lemme see a shot of the left side's slider. I want to see how much you had to cut.

Funny you should ask... I took a shot of the left side but it was all blurry and shit so I just deleted it. You can see it in the third-to-last photo on the table, and in the top part of the second-to-last photo you can see pretty well how much needs to be cut.

The left requires a significant amount more cutting than the right, but it's not a big deal.

The PITA that you probably haven't thought about yet is that those two side pieces slide into place, they have those little hook tabs that slide into the lower fairing... so after you cut a circular hole, you need to use a dremel to cut off some more on the rear portion of the circle... i.e. run a tangent line off of the circle. This allows you to slide the fairing in and out of place.

You follow what I'm saying here? Not sure if I'm explaining it well.

Also, the raw color of that plastic is light grey so you'll need to do something to it if you don't want it to be noticeable.

Originally Posted by TIGGER

I'll tell you one thing Motherfucker,if I EVER need sliders cut in...I'M CALLING YOUR ASS!!!!!! I don't think I've ever seen more perfectly cut sliders in my life!!! Good job! Oh and Dlit,if it's the same as my bike,they give you a sticker template to cut by with the kit.

Haha thanks dude. I'll help ya

No there was no sticker I just use a 2" hole saw that goes into a drill. Make sure you get the kind that has a pilot bit in the center for alignment purposes.


Little alignment trick: Get a laser pointer and stack in on top of things such that it's perfectly aligned with the center of the bolt head that holds the frame slider base into the engine. Then, don't move the laser pointer at all and mount up all your bodywork. Presto! Just put the center pilot bit of your hole saw on that mark and you're in business.